• August 22, 2019 2.9.8

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.8	Released August 22, 2019	Type ZIP	Filesize 3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 controller Graphics card with 24 or 32 bit Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Added several internal interfaces for particular sensors (J003).

• January 25, 2019 2.9.6

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.6	Released January 25, 2019	Type ZIP	Filesize 3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 controller Graphics card with 24 or 32 bit Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Added missing Tonemapping Auto property.

• May 4, 2018 2.9.5

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.5	Released May 4, 2018	Type ZIP	Filesize 3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 controller Graphics card with 24 or 32 bit Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Enabled tonemapping for 8bit video formats, e.g. Y800, RGB24 and RGB32.

• November 21, 2017 2.9.4

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.4	Released November 21, 2017	Type ZIP	Filesize 3.2MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Repaired not working J003 mono sensor pattern fix on particular video formats. This driver version is the last that works in Windows XP.

• January 9, 2017 2.9.3

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.3	Released January 9, 2017	Type ZIP	Filesize 3.2MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Added a pattern fix for J003 mono sensors.

• January 9, 2017 2.9.1

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.9.1	Released January 9, 2017	Type ZIP	Filesize 3.2MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Fixed the driver signature Code 52 error on new Windows 10 v1607 systems.

• January 15, 2016 2.8.9

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.8.9	Released January 15, 2016	Type ZIP	Filesize 2.3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Changed certificates so that the driver can also be installed in Vista.

• November 9, 2015 2.8.7

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.8.7	Released November 9, 2015	Type ZIP	Filesize 2.3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Fixed an error which can appear when using sharpness on older CPUs.

• October 20, 2015 2.8.5

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.8.5	Released October 20, 2015	Type ZIP	Filesize 2.3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Fixed a bug which can appear on LivePause call.

• July 15, 2015 2.8.0

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.8.0	Released July 15, 2015	Type ZIP	Filesize 2.4MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Support of DFK ECU010-L34 with serial number property. Added tone mapping.

• February 17, 2015 2.7.33

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.7.33	Released February 17, 2015	Type ZIP	Filesize 2.4MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog The Auto Focus Onepush Running flag now resets correctly after the auto focus has finished.

• February 5, 2015 2.7.32

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.7.32	Released February 5, 2015	Type ZIP	Filesize 2.4MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Video format MJPG (2592x1944) of DFK AFU050-L34 camera can now be used.

• January 14, 2015 2.7.31

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.7.31	Released January 14, 2015	Type ZIP	Filesize 2.3MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Support for IMX236 based cameras. Support for RGB64 color formats. Several performance improvements.

• June 6, 2014 2.7.9.1152

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.7.9.1152	Released June 6, 2014	Type ZIP	Filesize 2.1MB
  Requirements Intel Core i3 or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit), Windows 10 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Added new properties: Brightness, sharpness, de-noise, saturation, hue and contrast. Added new property: Highlight reduction. Added new property: White balance temperature controls. Pixelfix for Y16 cameras now works as expected. VideoControl_ExternalTrigger (DirectShow property) can now be set as expected.

• January 1, 2014 2.6.5.1014

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.6.5.1014	Released January 1, 2014	Type ZIP	Filesize 1.9MB
  Requirements Intel Pentium IV or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit) DirectX 9.0c or higher
  Changelog Fixed missing auto-gain for DFK AFU130. Fixed focus when start value is out of auto_focus_range. Fixed problem with AUTOFOCUS_ROI_RIGHT: minimum possibly wrong. Fixed auto focus ROI not working for 21*UC cameras. Fixed crash on load/connect with certain cameras 22/72xUC. Fixed previous exposure settings not being loaded on reconnect. Complete reworking of internal property system. Fixed Windows XP driver load crash. Fixed drop counter to be accessible from DirectShow. Fixed Windows 8 problem with certain video formats needing converters with standard DirectShow filters (e.g. Y800, capturing to an Y800 avi file was not possible). Fixed a problem with Windows 8 usbxhci driver not allowing transfers larger then 4 MB.

• February 26, 2013 2.4.14.851

  Device driver for all The Imaging Source USB cameras except the 33U, 37U, 38U and AFU auto focus series.
  Version 2.4.14.851	Released February 26, 2013	Type ZIP	Filesize 1.9MB
  Requirements Intel Pentium IV or similar, 2 GB RAM USB 3.0 or USB 2.0 controller (depends upon camera model) Graphics card with 24 or 32 bit Windows XP, Windows Vista, Windows 7 (32 & 64 bit), Windows 8 (32 & 64 bit) DirectX 9.0c or higher
  Changelog WHQL certification.

Please note that these drivers will only work for the v2.x versions of the Pololu USB AVR Programmer, not the original item #1300 Pololu USB AVR Programmer. If you have the original programmer, which has a green PCB instead of blue, you will need to install the drivers specific to that device.

For ATMEGA beginner user, installation of USB-ASP in Windows 10 can be tiresome. USBASP Device is inteded to work with 32 bits yet our current PC Windows 10 is mostly 64 bit. So extra steps are needed for a particular USB port. If you have installed USBASP on one of the a physical ports, you need to remember which port that you have installed with. Provide an INF file that specifies the Ports device setup class and the Serial function driver as the service for the port. To configure a serial port as COM port, comply with the requirements that are defined in Configuration of COM Ports. Connect the device to the windows PC. Install the driver for the device on the PC. Go to Device Manager, select this device (listed under Universal Serial Bus controllers) and right click and select Properties. Go to Driver tab in the Properties window, and click on Driver Details. Note the sys files listed there. 6) Monkey will connect to our server and download the appropriate drivers for your Line 6 device. 7) After the drivers are downloaded, Line 6 Monkey will exit so the Driver Install Wizard can launch. 8) Once the Line 6 Monkey prompts you to plug your device in, the Windows Found New Hardware Wizard should open. Please follow the. Available in this download is the current modem driver for 3Com modems bought before January 1996, operating under Windows 95/NT 4.0. Copy this file onto a blank floppy disk.

The Pololu USB AVR Programmer v2.x has drivers and configuration software for Windows. The drivers tell Windows how to recognize the programmer and set it up correctly. The drivers are needed for Windows Vista, Windows 7, and Windows 8. For Windows 10 and later, the drivers are optional but recommended. The configuration software allows you to change the programmer’s settings and can be helpful for troubleshooting.

Before connecting your programmer to a computer running Microsoft Windows, we recommend installing its drivers and software by following these steps.

1. Download and install the Pololu USB AVR Programmer v2 Software and Drivers for Windows (9MB msi). Please note that the drivers and software in this installer will only work with the Pololu USB AVR Programmer v2 and v2.1, which are blue-colored.
2. During the installation, Windows will ask you if you want to install the drivers. Click “Install” to proceed.
3. After the installation has finished, your computer should automatically set up the necessary drivers when you connect a Pololu USB AVR Programmer v2.x, in which case no further action from you is required.

After installing the drivers and plugging the programmer in via USB, if you go to your computer’s Device Manager, you should see three entries for the programmer as shown below:

Pirelli Port Devices Driver Download For Windows 10 Windows 7

Windows 10 Device Manager showing the Pololu USB AVR Programmer v2

The programmer configuration software consists of two programs:

• The Pololu USB AVR Programmer v2 Configuration Utility is a graphical user interface (GUI) for configuring the programmer and viewing its status. You can find the configuration utility in your start menu by searching for it or looking in the Pololu folder.
• The Pololu USB AVR Programmer v2 Command-line Utility (pavr2cmd) is a command-line utility that can do everything that the GUI can do. You can open a terminal and type pavr2cmd with no arguments to a see a summary of its options.

COM ports

In the “Ports (COM & LPT)” category of your Device Manager, you should see two COM ports with names like “Pololu USB AVR Programmer v2.1 Programming Port” and “Pololu USB AVR Programmer v2.1 TTL Serial Port”.

You might see that the COM ports are named “USB Serial Device” in the Device Manager instead of having descriptive names. This can happen if you are using Windows 10 or later and you plugged the programmer into your computer before installing our drivers for it. In that case, Windows will set up your programmer using the default Windows serial driver (usbser.inf), and it will display “USB Serial Device” as the name for each port. The ports will be usable, but it will be hard to distinguish the ports from each other because of the generic name shown in the Device Manager. We recommend fixing the names in the Device Manager by right-clicking on each “USB Serial Device” entry, selecting “Update Driver Software…”, and then selecting “Search automatically for updated driver software”. Windows should find the drivers you already installed, which contain the correct name for the port.

If you are using Windows 10 or later and choose not to install the drivers, the programmer will still be usable. See Section 4.5 for information about determining which COM port is which.

If you want to change the COM port numbers assigned to your programmer, you can do so using the Device Manager. Double-click a COM port to open its properties dialog, and click the “Advanced…” button in the “Port Settings” tab. Windows will associate this COM port number with the USB serial number of your programmer and use it whenever you plug that programmer in. If you have multiple programmers but only plug in one at a time, it can be helpful to assign each programmer to the same set of COM ports.

Native USB interface

There should be an entry for the programmer in the “Universal Serial Bus devices” category with a name like “Pololu USB AVR Programmer v2.1”. This represents the programmer’s native USB interface, and it is used by our configuration software. The programmer’s native USB interface implements Microsoft OS 2.0 Descriptors, so it will work on Windows 8.1 or later without needing any drivers. The driver we provide is needed for earlier versions of Windows.

USB troubleshooting for Windows

If the software you are using cannot communicate properly with the programmer, a good first step is to just unplug it from everything and then plug it back in again.

You should also make sure you are specifying the right COM port name in your software. AVR programming software should usually connect to the programmer’s programming port. If you want to communicate using the RX and TX lines, you should connect to the TTL serial port. You can find the right COM port names by following the instructions in Section 4.5.

If that does not work, you should try to locate all the entries for the programmer in the Device Manager. Be sure to look in these categories: “Other devices”, “Ports (COM & LPT)” and “Universal Serial Bus devices”. It might help to click “View”, select “Devices by Connection”, and then expand entries until you can find entries relating to the programmer. When viewing devices by connection, the programmer is normally represented by a “USB Composite Device” entry that has three child entries which should look like the entries shown in the screenshot above. Any entry corresponding to the programmer might have an incorrect name if the wrong driver is installed or there was an error. You can tell if an entry corresponds to the programmer by unplugging the programmer and checking to see whether the entry disappears. Finding the programmer’s entries in the Device Manager can often give you a good idea of what is wrong.

If the programmer has no entries in your Device Manager, you probably have a low-level hardware problem. Try using a different USB cable and a different USB port. Make sure your cable is not a charging-only cable.

If the programmer does have entries in the Device Manager, but they don’t look like the screenshot above, then you might have a driver installation problem. To ask Windows to use the right drivers, you can right-click on each entry, select “Update Driver Software…”, select “Browse my computer for driver software”, and then enter the location of the “drivers” folder for the programmer. This is typically “C:Program Files (x86)PololuUSB AVR Programmer v2drivers”.

Do not attempt to fix driver issues in your Device Manager using the “Add legacy hardware” option. This is only for older devices that do not support Plug-and-Play, so it will not help. If you already tried this option, we recommend unplugging the programmer from USB and then removing any entries you see for the programmer by right-clicking on them and selecting “Uninstall”. Do not check the checkbox that says “Delete the driver software for this device”.

The Pololu USB AVR Programmer v2 Configuration Utility in Windows 10.

Related products

Pirelli Port Devices Driver Download For Windows 10 7

Pololu USB AVR Programmer v2

Pololu USB AVR Programmer v2.1